Welcome to Würth Greece For trade customers only
Plastic frame anchor SHARK<SUP>® </SUP>UR F Zinc-plated steel - ANC-SHARK-URF8-PLA-AW25-WS10-70/50-8X120

Plastic frame anchor SHARK® UR F Zinc-plated steel

Plastic frame anchor SHARK UR F steel zinc plated
ANC-SHARK-URF8-PLA-AW25-WS10-70/50-8X120
ZEBRA

Art.-no. 5912808605
EAN 4065746348379
All versions

Prices for customers after login

Exclusively for trade customers

Register now and access more than 125,000 products

Plastic frame anchor with comprehensive ETA rating for masonry, aerated concrete and concrete. With hexagon head bolt and pressed washer made of zinc-plated steel
  • Part of the SHARK® UR product family, which has been tested in connection with more than 100 building materials as part of ETA-08/0190

  • The SHARK® UR 8 and 10 frame anchors are tested and approved for a total of 105 different surfaces. In addition to concrete and aerated concrete, numerous bricks are included in the current most comprehensive ETA assessment, including solid and perforated brick, hollow and solid sand-lime bricks, solid and perforated concrete bricks and hollow blocks made of lightweight concrete

  • Thanks to the ingenious anchor geometry, the "teeth" spread in four directions and claw right down into the base material

  • Anchorage via friction locking between anchor sleeve and base material

  • Anchor sleeve made of high-quality polyamide

  • Push-through installation

  • Can be loaded immediately - no waiting

  • Very strong anti-rotation lock

  • High load-bearing capacity thanks to expansion in four directions

  • Improved load transfer through even, continuous load distribution across the entire expansion area

  • The hammer-in stop prevents premature expansion of the anchor during installation

  • Less installation work, as the anchor sleeve and special screw are pre-assembled

  • Improved load transfer in solid and hollow construction materials
Proof of Performance
  • SHARK-UR F 10 (zinc-plated steel, stainless steel): European Technical Assessment ETA-08/0190

  • Expert report on fire resistance duration in the event of fire exposure

Drill the hole

Remove drill cuttings

Check temperature of anchor sleeve

Check temperature of substrate

Install the anchor and screw with a hammer

Screw in dowel

Screw in screw until flush
  • SHARK-UR F 10 (zinc-plated steel, stainless steel): European Technical Assessment ETA-08/0190

  • Expert report on fire resistance duration in the event of fire exposure
Product information

Würth Catalogue

Datasheets(X)

Certificates/ Documents

 | 

 | 

Application area
  • This anchor with a European Technical Assessment may be used as a fastener in a redundant non-structural system for non-load-bearing constructions (e.g., façades, suspended ceilings, etc.)

  • SHARK UR, SHARK UR F can be anchored in the following anchoring substrates: Standard concrete, masonry walls (solid brick, solid sand-lime brick, vertically perforated brick, hollow sand-lime brick, hollow lightweight concrete blocks, solid bricks and blocks made of lightweight concrete, concrete bricks) and aerated concrete

  • Two setting depths in defined building materials

  • Installation temperatures: Temperature of anchoring base: ≥ -20°C

  • Temperature of anchor sleeve: ≥ 0°C

  • The electrolytically galvanised screw can be used outdoors or in damp areas (if installed carefully) provided that the area around the screw head is protected against moisture or rain so that moisture cannot penetrate into the anchor shaft. Permanently elastic sealant such as art. no. 0892 075 350 Gravel throw and underbody seal 500 ml

  • Suitable for mounting façade, ceiling, and roof substructures (made of wood or steel), wooden beams, wooden laths, metal brackets, metal rails, suspended ceilings, cable conduits, brackets, profiles, wall-mounted cabinets, shelves, etc.

  • Mountings where proof of load-bearing capacity under exposure to fire is required
Instructions
  • Drill perforated and hollow blocks with a rotary drill (without hammer mechanism)

  • Drill cuttings must be removed from the drilling hole, e.g., with the blow-out pump art. no. 0903990001

  • Drilling in concrete with a suction drill saves having to clean the drill hole

Anchor diameter

8 mm

Anchor length (l)

120 mm

Max. attachment height (t fix)

70 mm

Nominal drill-bit diameter (d 0)

8 mm

Through-hole in the component to be connected (d f)

8.5 mm

Fire resistance rating

F30

Attachment height (t fix 1)

70 mm

Material of screw

Steel

Internal drive

AW25

Surface of the screw

Zinc plated

Head type

Hexagon head

Approval

ETA-08/0190

Type description

W-UR F 8, hexagonal bolt

Zinc-plated steel
A4 stainless steel
1) The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of γF = 1.4 have been taken into account. For the combination of tensile and transverse loads, please refer to ETAG 020 Appendix C
2) Maximum long-term temperature
3) Maximum short-term temperature
Normal weight concrete solid brick Vbn,
EN771-3, DIN 18152 		≥ NF (≥ 240 x 115 x 71) ≥ 2.0 10 0,43
20 0,71
28 1,00
Vertically perforated brick HLz6),
EN 771-1, DIN 105-1
e.g. Wienerberger, Schlagmann 		≥ 2DF (≥ 240 x 115 x 113) ≥ 1.2 8 0,21
12 0,26
20 0,43
Vertically perforated brick POROTON S11-36.56),
EN 771-1, Z-17.1-812
Wienerberger, Schlagmann 		≥ 248 x 300 x 249 ≥ 0.6 6 0,26
Vertically perforated brick POROTON S11-36.56),
EN 771-1, Z-17.1-812
Wienerberger, Schlagmann 		≥ 248 x 356 x 249 ≥ 0.9 6 0,57
Hollow sand-lime brick KSL6),
EN 771-2, DIN 106-1
e.g. Xella 		≥ 2DF (≥ 240 x 115 x 113) ≥ 1.6 10 0,57
12 0,71
16 0,71
≥ 8DF (≥ 249 x 240 x 238) ≥ 1.4 10 0,26
12 0,34
16 0,43
Hollow block made of lightweight concrete 3K Hbl,
EN 771-3, DIN 181516) e.g. Liapor 		≥ 16DF (≥ 498 x 240 x 238) ≥ 0.7 2 0,10
4 0,26
6 0,34
Hollow block made of lightweight concrete
Liapor-Super-K6),
EN 771-3, Z-17.1-501 		≥ 16DF (≥ 495 x 240 x 238) ≥ 0.8 2 0,17
4 0,34
Aerated concrete AAC 2 0,14
7 0,85
2) Maximum long-term temperature
3) Maximum short-term temperature
4) For other types of stone, raw densities, minimum pressure strength or temperature ranges, please refer to the approval ETA-08/0190
5) The stone geometry should be compared with the approval ETA-08/0190
6) If the drill hole is created through impact or hammer action, the permissible load must be determined by tests on the structure
Plain concrete solid brick Vbn,
EN771-3, DIN 18152 		≥ NF (≥ 240 x 115 x 71) ≥ 2.0 10 0,57
20 0,86
28 1,29
Vertically perforated brick HLz6),
EN 771-1, DIN 105-1
e.g. Wienerberger, Schlagmann 		≥ 2DF (≥ 240 x 115 x 113) ≥ 1.2 8 0,21
12 0,34
20 0,57
Vertically perforated brick POROTON T8-306),
EN 771-1, Z-17.1-982
Wienerberger, Schlagmann 		≥ 248 x 300 x 249 ≥ 0.6 6 0,26
Vertically perforated brick POROTON S11-36.56),
EN 771-1, Z-17.1-812
Wienerberger, Schlagmann 		≥ 248 x 356 x 249 ≥ 0.9 6 0,43
Hollow sand-lime brick KSL6),
EN 771-2, DIN 106-1
e.g. Xella 		≥ 2DF (≥ 240 x 115 x 113) ≥ 1.6 10 0,43
12 0,57
16 0,71
≥ 8DF (≥ 249 x 240 x 238) ≥ 1.4 10 0,34
12 0,43
16 0,57
Hollow block made of lightweight concrete 3K Hbl,
EN 771-3, DIN 181516) e.g. Liapor 		≥ 16DF (≥ 498 x 240 x 238) ≥ 0.7 2 0,09
4 0,17
6 0,26
Hollow block made of lightweight concrete
Liapor-Super-K6),
EN 771-3, Z-17.1-501 		≥ 16DF (≥ 495 x 240 x 238) ≥ 0.8 2 0,17
4 0,34
Aerated concrete AAC 2 0,21
7 0,88
2) Maximum long-term temperature
3) Maximum short-term temperature
4) For other types of stone, raw densities, minimum pressure strength or temperature ranges, please refer to the approval ETA-08/0190
5) The stone geometry should be compared with the approval ETA-08/0190
6) If the drill hole is created through impact or hammer action, the permissible load must be determined by tests on the structure
Zinc-plated steel
A4 stainless steel
1) The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of γF = 1.4 have been taken into account. For the combination of tensile and transverse loads, please refer to ETAG 020 Appendix C
2) Maximum long-term temperature
3) Maximum short-term temperature

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Würth Catalogue

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information
Show all product details