1-component gun foam Streetfighter
1C gun foam Streetfighter
GUNFM-1C-B3-STREETFIGHTER-750ML
Register now and access more than 125,000 products
Excellent adhesion to virtually all construction surfaces (with the exception of PE, PP, PTFE and silicone)
Better sound and heat insulation properties than mineral wool, cork and fibreglass
Dimensionally stable
No volume shrinkage and only minimal post-expansion once the product has fully hardened.
Quick to fully harden
Fine-celled and uniform foam structure
Resistant to ageing
Resistant to a large number of solvents, paints and chemicals
Primer should be applied to porous and absorbent surfaces. PURLOGIC® Streetfighter can be applied with PURLOGIC® Xpress, art. no. 0891 152 4, and PURLOGIC® COMBIpress, art. no 0891 152 6, foam guns.
The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. We do not assume any liability for a specific application result due to the large number of applications and storage and processing conditions. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting with deliberate intent. We guarantee the consistent quality of our products. We reserve the right to make technical changes and carry out further development.
Datasheets(X)
Secure insulating and filling of window joints, pipe openings, joints, wall joints, wall openings and cavities, such as wall openings, roof finishings, pipe ducts, roller shutter boxes etc. Adheres to concrete, stone, hard PVC, metal and wood. Does not adhere to polyethylene, silicone, PTFE and grease.
Shake can vigorously 20 times before use. The surfaces must be clean, solid and free from dust and grease. Pre-treat highly absorbent surfaces. Adhesion surfaces must be moistened with water before the foam is applied. Moisten again if several foam beads are applied. Screw the can all the way into the gun support – do not screw too far or tilt. Foam continues to expand after application. Immediately remove splashes of foam with PURlogic Clean, art. no. 0892 160. Thoroughly clean the gun and valve after use. Always leave the open can screwed onto the gun.
Chemical basis | Single component polyurethane |
Colour | Yellow |
Smell/fragrance | 0 - not applicable |
Moulded density | 18 kg/m³ |
Cell structure | Medium - fine |
Cell structure conditions | tested in accordance with Würth test methods |
Tack-free after | 15 min |
Conditions for being tack-free | at 20°C |
Can be cut after | 100 min |
Conditions for ability to cut | tested in accordance with Würth test methods |
Full resilience | 24 h |
Conditions for full resilience | 0 - not applicable |
Min. processing temperature | 5 °C |
Max. processing temperature | 35 °C |
Min. surface processing temperature | 5 °C |
Max. surface processing temperature | 35 °C |
Min. temperature resistance | -40 °C |
Max. temperature resistance | 90 °C |
Building material class | B3 - Of high flammability |
Building material class conditions | 0 - not applicable |
Min. tensile strength | 40 kPa |
Ultraviolet resistance | 0 - not applicable |
Contents | 750 ml |
Container | Aerosol can |
Weight of content | 740 g |
Shelf life from production | 18 Month |
Conditions to maintain shelf life from production | at 10°C to 35°C, no exposure to sunlight, no heat sources |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Sandpaper, waterproof Aluminium oxide
Sealing ring
TIME-SERT® threaded bushing
Black NBR70 round cord
Self-adhesive base
Ratchet with square insert shank 9x12 mm
Non-slip adhesive tape for wet areas
Maintenance set For 1/4 inch and 3/8 inch reversible ratchet with turntable
pias® drilling screw with hexagon head and drill tip Case-hardened steel, zinc-plated, blue passivated
Stainless steel care spray